Window regulator programming and training
Content
If you are faced with such a situation that after removing the car battery you have power window closers stopped working, then this article will help solve this problem. Below you will find information on various cars and modifications, the information will be supplemented with new models as they become available.
Power window training, repairing a broken door closer
Closer does not work - what is the reason?
The reason is that the commands to the window regulator mechanism are given by power window control unit... When disconnecting the battery terminals, the settings of the control unit for the closers are usually reset. Naturally, on each car model, the training of power windows is done differently:
Window regulator training for Mercedes Benz W210
- Lower the glass completely in non-automatic mode (without pressing the closer keys). After the glass has lowered to the end, immediately press the closer mode and hold for about 5 seconds.
- Further, similarly for the upper position, raise the glass in non-automatic mode and at the end switch to automatic mode (closer mode) and also hold for 5 seconds.
These manipulations must be done with the window regulator of each door separately. There is a chance that the control unit will not learn the first time, just try again.
Power window training for Ford Focus
- Raise the window regulator button and hold it until the glass rises completely.
- Raise the button again and hold it for a couple of seconds (usually 2-4 seconds).
- Press the window regulator button and hold it until the glass is completely lowered.
- We release the window regulator button.
- Lift the power window button, hold it until the glass is fully lifted.
- Open the window and try to close it automatically (with a single key press).
If, after the actions taken, the window did not close automatically to the end, then repeat the procedure from step 1 again.
COMMENT! On Russian-assembled Ford Focus 2 models, this algorithm works only if all 4 power windows are included in the package. (If only 2 front ones are installed, the algorithm will not work)
Power window training for Toyota Land Cruiser Prado 120
If the windows stopped working in auto mode after removing the battery and the button illumination does not light up, but blinks, then the following algorithm will help to cope with this problem.
- The car must be started or the ignition must be turned on.
- Press the glass release button and hold until the glass is completely open. After it has opened, hold the button for another 2-4 seconds and release.
- Similar steps for lifting the glass. After fully raising the glass, hold the button for a few more seconds and release.
- Similarly for all other power windows, follow steps 2 and 3.
After these actions, the flashing of the backlight should turn into a normal constant backlight and the windows should work in auto mode.
COMMENT! Training of each window regulator must be carried out from the button of the exact door that you are teaching. It is not possible to train all windows from the driver's buttons.
Power window training for Mazda 3
Programming power windows on Mazda 3 is carried out similarly to training on Mercedes, described above in the article. In other words, using the window regulator button for each door (we use that button related to a specific door, not the driver's panel), first completely lower the glass and hold the button for 3-5 seconds, then raise it to the end and also hold it for 3-5 seconds. Done.
Questions and answers:
Why does the window lifter slowly raise the glass? 1 - lack of lubrication or little. 2 - incorrect glass adjustment (incorrectly on the bar). 3 - a manufacturing defect. 4 - wear of glass seals. 5 - problems with the motor.
The main reasons for the failure of the window regulator. 1 - road accident (hit on the door). 2 - moisture has entered. 3 - factory defect. 4 - electrical problems (fuse, poor contact, motor wear). 5 - mechanical failures.
22 comment
Mazdos
And how to teach on the Mazda 3rd? Tell me !!!
Valentine
In paragraph 6 for the Ford Focus, it is not clear what “open the window” means. So repeat step 3?
TurboRacing
The 6th point is to check the result, whether it works or not. Just open the window as usual and try using a door closer.
TurboRacing
Added information on Mazda to the article. Thanks for the question.
Egor
Hello, I changed the window regulator control unit for a suzuki escudo 3-door cars do not work, tell me how to teach, thanks in advance!
TurboRacing
Your windows do not work at all?
The fact is that programming / learning is done in order to set up an automatic mode (closer).
With a completely inoperative mechanism, the matter is most likely either in the control unit itself, or in its incorrect connection.
Egor
The power windows work, the button of the new unit says “drive”, the driver’s button does not work in automatic mode (closer), I connected it to a regular chip, I didn’t change the circuit.
Arthur
I have a focus of the second Russian assembly, only two window lifters, how to set it up so that when closing it does not go down on its own, please tell me
TurboRacing
Please clarify your question, what does it mean when you closed it did not go down by itself. It rises when closed 🙂.
Michael
Hello. Tell me how to program the auto mode on a Suzuki Grand Escudo. Thank you.
TurboRacing
Hello.
Try the following option: with the ignition on, manually lower the glass to the end and without releasing the button, hold it in the “auto” mode for about 10 seconds. Raise the glass in the same way.
If that doesn't work, try doing the same with the door open.
Basil
Hello. I have a Nissan Serena, two windows, so when the alarm is activated, one window closes, then it is necessary to disarm and re-arm, the second will work. For some reason, they cannot synchronously. I changed the battery, after that it all started.
Rostislav
Please tell me how to train glasses on Suzuki CX4
TurboRacing
On a Suzuki SX4, the factory does not provide full-fledged door closers for all windows.
The “Auto” mode (auto-lowering) is only on the driver's window and only works down. Those. the glass will have to be raised manually. All other windows are raised/lowered manually.
Michael
Hello. Auto mode does not work correctly. On the contrary, it is restored and works as it should. But basically, when lifting to the end, it returns to a certain height. Seems like the anti-jamming is working. And the other day the auto mode stopped working altogether, neither up nor down did not work at all. Now down works, and up returns. The window regulator lives its own life. I disassembled the block, soldered everything, washed it in alcohol, it didn’t help. Tell me what to do. Thank you.
lomaster
Guys, all glass lifts do not work except the driver's one, not from the door buttons, not from the control unit on the driver's door, which may be
Sayad
on Mercedes w202, after replacing the battery, for whom the automatic window regulator does not work correctly, open all the glass, get out of the cars, press and hold the door closing until the window is closed (about 5 seconds).
Samvel
Ford focus 1 made according to the scheme, the closer mode is working properly. Thank you!
Hovik
hello, I have a lot of bullshit, the power windows work well, but when I start the car, the windows and the sunroof will stop working, as asked?
Oleksandr Trush
Please tell me about KIA soul ev. When closing the car, the windows do not rise. Sincerely grateful
Rudolf
I need advice on the Škoda Rapid spaceback. The driver's window can be opened automatically, but it can only be closed manually. Passenger only manually. Can something be done with it?
Yura
Who knows how on a BMW